Sep 16, 2020

Telescopic Hydraulic Cylinder Material 27SiMn Tube Processing Technology Before Machining

Leave a message

Telescopic Hydraulic Cylinder material 27SiMn tube processing technology before machining

 

 

Preface

The cylinder tube is the key element that forms the inner cavity to contain fluid. Therefore, the comprehensive performance of the cylinder barrel, such as pressure resistance, wear resistance, and fatigue strength, plays a key role in the life of the telescopic hydraulic cylinder.

Generally, the cylinder tube is required to be able to withstand the pressure within 22MPa (continuous pressure), even up to 55MPa. Therefore, in the production of telescopic hydraulic cylinder tube, the technical conditions of the steel pipes for the cylinder barrels are clearly defined. The tube for telescoping cylinder usually adopt the following processes: stress relief annealing process, normalizing heat treatment process, quenching and tempering heat treatment process, etc. The tube produced by the above heat treatment processes have different technical properties and are suitable for Hydraulic cylinders working in different environments.




1. Technical conditions of tube telescopic cylinder


When making 27SiMn material to product telescoping hydraulic cylinders, the technical requirements for tube are as follows.

1.1   Chemical composition:                                                                                                          C:0.24~bai0.32 Si:1.10~1.40 Mn:1.10~1.40 P:≤0.035 S:≤0.035 Cu:≤0.30 Cr:≤0..

1.2   Mechanical properties

Tensile strength Rm≥860MPa, yield strength ReH≥760MPa; elongation rate A5≥12%, shrinkage rate Ψ≥40%; impact energy AkV2(20℃)≥39J; hardness 240∼280HBW

       1.3 Process performance

Pressure test at room temperature can withstand 25~30MPa pressure (continuous pressure)

       1.4 Metallographic organization

Decarburization layer ≤0.20mm; in terms of macrostructure, the general looseness, center looseness, and segregation of the steel pipe are ≤2, and there should be no shrinkage cavity, subcutaneous bubbles, white spots, peeling, delamination, cracks and other inclusions. ; The metallographic structure is tempered sorbite + pearlite, level 3.

       1.5 Surface roughness

             Surface roughness Rа≤12.5µm

       1.6 Geometry accuracy

The dimensional tolerances of the inner and outer diameters are both ±0.15mm

 

2.   2/3/4/5 Stage Telescopic Cylinder Tube Quenched and tempered heat treatment process

To meet the technical requirements of single or double acting telescopic hydraulic cylinders used in complex environments, to make the tube have sufficient strength, hardness, toughness, pressure resistance and fatigue resistance, it is the most ideal choice to adopt a quenched and tempered heat treatment process to adjust the comprehensive mechanical properties of the material

 

2.1 Conventional quenching and tempering heat treatment process

In order to make the tube for cylinder tube have excellent characteristics such as high strength, high hardness, good wear resistance, strong plasticity, high pressure resistance, small deformation, less decarburization and long fatigue life, the tube heat treatment is implemented according to the following process.

According to the characteristics of the 27SiMn material, the specific quenching and tempering heat treatment process is: heating to 910∼920℃, holding for 35min and then water cooling; then adopting tempering heat treatment at 510∼520℃ for 180min.

After this heat treatment, the tube surface roughness is 12.5μm, and the thickness of the decarburized layer is 0.10mm; the metallographic structure is tempered sorbite + pearlite + semi-network, strip, block, acicular ferrite ( Figure 3), 5 grades of grain size; withstand pressure of 30 MPa (last 10s).

 

 

Analyze the test results and get:

①     After the telescopic hydraulic cylinder tube is quenched and tempered and heat treated, the tensile strength, yield strength, elongation, reduction of area, impact energy, surface finish, and depth of decarburization all meet the technical requirements of hydraulic cylinders;

②     The telescopic hydraulic cylinder tube is severely deformed after quenching and tempering heat treatment, which cannot meet the technical requirements of the hydraulic cylinder;

③     After the telescopic hydraulic cylinder tube undergoes quenching and tempering heat treatment, the metallographic structure of the tube is tempered sorbite + pearlite + semi-reticulate, strip, massive, acicular ferrite, with a grain size of grade 5, which fails to reach the level of the hydraulic cylinder barrel. skills requirement.

 

2.2 Analysis of the reasons for the poor effect of quenching and tempering heat treatment process

2.2.1 The geometric accuracy of the steel pipe produces serious deformation

When the tube is quenched at high temperature, due to the effect of the rapid cooling of the cooling medium, the phenomenon of thermal expansion and contraction occurs instantaneously, and the residual stress of the tube itself is poor, resulting in serious deformation of the tube with accurate tolerance after being quenched and tempered. Therefore, it is necessary to adopt a heat treatment process to completely eliminate stress and stabilize the structure before quenching and tempering, which can effectively prevent the deformation of the tube during quenching and tempering.

 

2.2.2 Metallographic organization does not meet the requirements

(1) The temperature during heating of the above quenching and tempering process cannot meet the requirements of metallographic structure transformation. Too low a quenching temperature will cause the ferrite to not completely dissolve and not fully austenitize. In this case, cooling and quenching are performed, so that the massive ferrite that has been precipitated before quenching gradually increases with the decrease of temperature and the extension of time

 (2) The martensite transformation is not complete. The austenite must be cooled to the martensite transformation start temperature Ms at a cooling rate greater than the critical cooling rate before martensite transformation can occur. Martensite transformation is different from pearlite transformation. When austenite is cooled to any temperature below the Ms point, it generally does not need to be inoculated. The transformation starts immediately and proceeds very quickly, but the transformation stops quickly and cannot be completed. .

In order for the transformation to continue, the temperature must be lowered. When the temperature drops to the martensite transformation end temperature Mf, the martensite transformation can no longer proceed. Even if it is cooled below Mf, the martensite transformation amount has not reached 100%, but the martensite transformation has stopped, and there is an incomplete martensite transformation phenomenon. Therefore, in this quenching and tempering process, it is necessary to appropriately increase the quenching temperature and holding time to accelerate and ensure the austenite transformation. At the same time, the 27 simn tube adopts water spray cooling when cooling to avoid the disadvantages of cooling with a cooling water tank (the 27 simn tube enters the water tank for cooling immediately after being out of the furnace, and it cannot guarantee the martensite transformation temperature Ms point. The body transformation can continue. The martensite transformation can only be carried out under the condition of continuous cooling. When the water tank is cooled, the tube is directly cooled to the temperature of the water tank cooling water, which cannot effectively reflect the Ms point). Because the Ms point of this material is 355℃, after spraying water to cool to this Ms point temperature, the martensite can be effectively and completely transformed under the condition of continuous water spraying, otherwise there will be incomplete austenite transformation and retained austenite organization

 

(3) The cooling medium cannot achieve the rapid thermal diffusion cooling effect of the tube during quenching. When tap water is directly used to cool the steel pipe, the cooling rate is too fast, the local cold shrinkage is uneven, the substance in the structure is not diffused enough, the internal stress is large, and the pipe is prone to cracking and deformation. In order to make the quenching cooling medium have the characteristics of uniform cooling temperature, small temperature difference, and fast cooling speed, the general quenching technology is to add salt and other mixtures in tap water, especially in the quenching and cooling of alloy steel. The quenching cooling adopts salting measures, which can satisfy Different isothermal temperature and cooling rate requirements. Therefore, it is necessary to add 5% to 10% of industrial salt to the cooling water to achieve the effects of uniform temperature, small temperature difference, fast cooling speed, and uniform internal structure of the material.

 

2.2.3 The influence of heating and cooling rate on the metallographic structure and deformation of tube

The heating and cooling rate is very critical in the heat treatment process. For large workpieces, special-shaped parts, pipes, etc., there are design defects that are not conducive to heat treatment. The heating and cooling speeds need to be limited to a certain range, otherwise it will cause excessive temperature differences in various parts of the workpiece and cause the workpiece to heat up Stress-deformation damage, thermal stress and deformation, and at the same time can affect whether the austenitization process is complete.

 

(1) Limit the heating rate. Limiting the heating rate is to heat each part of the tube more uniformly. If the heating rate is too fast, part of the structure will not be austenitized, and troostite will be formed at the beginning of cooling, which will not only affect the uniformity of austenitization, but also cause after quenching The grains are coarse, even intergranular cracks appear, and the steel pipe will be deformed. At the same time, the heating speed affects the microstructure of the material. During the heating process, the speed is fast, and part of the second phase has no time to dissolve.

(2) Increase the cooling rate. During annealing, the cooling rate should be slow, but during quenching and cooling, under the premise of ensuring micro deformation and no cracking, the faster the better. The cooling rate directly affects the structure formed by quenching, and the quenched structure martensite can only be obtained at a certain speed.

Therefore, the heating and cooling rate directly affects the crystallization rate and deformation probability of the steel pipe. Only by accurately controlling the heating and cooling rate in this heat treatment process can the metallurgical structure of the metal material be guaranteed and the deformation of the tube can be avoided.

 

2.3 Improved quenching and tempering heat treatment process

According to the above analysis, the heat treatment process for the steel pipe for tube to completely eliminate the stress and stabilize the structure is adopted; then the quenching and tempering process for the steel pipe is adopted.

 

After the above quenching and tempering heat treatment process, the tube is tested, and its geometrical dimensional accuracy, straightness and performance are very good; the tube surface roughness is 12.5μm, the thickness of the decarburization layer is 0.15mm; the steel tube has no residual shrinkage, subcutaneous bubbles, White spots, peeling, delamination, cracks, etc., center porosity and segregation are all at level 2, and the metallographic structure is at level 3 (tempered sorbite + ferrite) (Figure 7); withstand pressure 35∼38MPa( Lasts 10s).

 

After the telescopic hydrauli cylinder tube undergoes quenching and tempering heat treatment, except for the change in straightness, the other comprehensive indicators fully meet the technical requirements of the hydraulic cylinder tube and achieve the expected purpose. The reason for the change in the straightness of the steel tube is that due to the difference in residual stress in each part of the tube, and during high-temperature quenching, it is affected by the rapid cooling of the cooling medium, causing instant thermal expansion and contraction, causing the steel tube to bend after quenching and tempering.

The effective measures to solve the serious bending of the tube after quenching and tempering are:

The tube needs to undergo preliminary pre-correction. After the quenching and tempering process is completed, the steel pipe will be subjected to final finishing so that the steel pipe can fully meet the technical requirements of the telescopic hydraulic cylinder.

 

Conclusion

The adjusted quenching and tempering process has passed many repeated practical tests and conducted analysis and demonstration. It makes full use of the alloy steel containing alloying elements and has strong hardenability characteristics, adopts the quenching and tempering process to improve the comprehensive performance of the material, and adopts the tube before quenching and tempering. The heat treatment process to completely eliminate the stress and stabilize the structure in the first stage, and then adopt the quenching and tempering (quenching + tempering) heat treatment process to adjust the comprehensive mechanical properties of the material, so that the steel pipe has high strength, high hardness, good wear resistance, strong plasticity, and pressure Comprehensive performance advantages such as large size, less decarburization, and slight deformation, fully meet the technical requirements of telescopic hydra













Send Inquiry